The Minimal Complete Typewriter Collection by [[Joe Van Cleave]]

Joe Van Cleave's personal six categories in a (his) typewriter collection: - Standard manual - medium-sized portable (largest segment in the collector's space) - lightweight portable or ultra-portable - typebar electric - IBM Selectric - Electronic typewriter (thermal typewriter), portable, quiet, battery operation.

Joe's minimal collection based on what he's got in his collection currently and the condition that they're in: - Royal KMM (his only standard) - Hermes 3000 (boxy middle era) - Olympia Splendid 33 (he's also got a Royal Mercury & Groma Kalibri) - Olympia Reporter - Selectric I (the only one he's got) cloth, ribbon cartridge system, no lift-off correction - Canon Typestar 220

Some of Joe's most important criteria in a typewriter: he prefers an elite face, 1 1/2 spacing, and bichrome setting.

At the time of this recording Joe had 30 typewriters.

Olympia SM3 Carriage removal timestamp 5:14

Actual removal process timestamp 10:46

Mainspring and drawband for Olympia SM3 tips just after 5:14 in the video

Olympia SM3 Carriage replacement timestamp 17:32

Olympia SM-3 SM-4 Typewriter Platen Roller Variable Ratchet Disassembly Repair Fix Plunger by [[Phoenix Typewriter]]

1958 Olympia SM3 Final Type Test -Part6: COMPLETE Olympia SM3 service and set up guide. by [[The HotRod Typewriter Co.]]

Gerren prefers cotton ribbons in pica machines because the larger typeface can better handle the ink.

Part 4: COMPLETE Olympia SM3 Service and Repair Series: STICKY RIBBON LIFTER by [[The HotRod Typewriter Co.]]

The universal bar lifts the ribbon vibrator.

Adjustment points to adjust the ribbon lift heights for issues with red/black on bichrome use.

Maximum travel of the universal bar adjustment screws on crossbar that attaches to springs. timestamp 5:29

Screws at the ends of the cross bar which are attached to the key springs can be adjusted slightly to provide for heavier or lighter touch control. Timestamp 6:07

https://www.youtube.com/playlist?list=PLUkDy-CP92u0XQ4oAl4nCsgid72Z9dl4E

Adjustment screw for the Olympia SM3 on feet shift set up is just to the side of the ribbon spool/cup. Gerren indicates that he's never been able to do this adjustment properly with the typewriter body on, so it's much easier to do with it off.

The bottom adjustment point (through the side of the frame) allows one to set the base line for the on foot for the lower case letters while the top one sets the upper case.

Gerren credits Phoenix Typewriter for most of the material he's learned in terms of fixing typewriters.

Bill at Philly Typewriter has an apprentice program, but there aren't many shops that do this. (Gerren makes a joke that it's free (child) labor.)

Trip point adjustments

The trip point is the point at which the typebar trips the movement of the escapement.

The adjustment point for it is reachable by removing the small protecting plate on the bottom at the back of the machine. The escapement trigger is just underneath it.

The lower one (top if the machine is upside down) is for the lower case; the top one is for the upper case.

Screwing the screw in will cause the trip to occur sooner.

Spacebar adjustment mechanisms [13:00]

There are two, one set in the front of the bottom of the typewriter and two screws in the back, right near the escapement.

If the spacebar is hit too many times while cleaning and repairing, the spacebar won't work properly and will need some minor adjustment when the body is put back on.

He shows at the end how to remove the keytops of the individual keys.

The final check is the shift lock mechanism to make sure its aligned properly.

Olympia SM3 (1/2/4/5/7) Silent Return Spring Fix Part 5: Complete Olympia Service and Repair Series by [[The HotRod Typewriter Co.]]

Removal of SM3 carriage with one screw and bolt.

Repairing silent return spring (also works for Hermes and other European models) which operates via friction. American models don't have this sort of mechanism, so one will always get the zipper sound moving the carriage back.

Part 3.5: COMPLETE Olympia SM3 service guide and tutorial: NICE RACK! Jammed carriage issues by [[The HotRod Typewriter Co.]]

Quick Tip- Platen Shim Install Olympia SM3 SM4 SM Portable Typewriters by [[The HotRod Typewriter Co.]]

Eraser Table Spring install Olympia SM3/4 by [[The HotRod Typewriter Co.]]

Script Olympia SM3 Disassembled in 5 minutes. Time Lapsed by [[The HotRod Typewriter Co.]]

Basic breakdown of the Olympia SM3 body parts, platen, etc. for cleaning.

Steps: - platen, etc...

Typewriter Video Series - Episode 173: Olympia SG-3 by [[Joe Van Cleave]]

Olympia SM Typewriter Wash, Scrub Clean Lid Cover, Restore Paint by [[Phoenix Typewriter]]

Simple Green gets off most dirt and nicotine as well as some White Out. Duane uses Nu-Trol Control Cleaner (for electronics) as a mild specialty cleaner for tougher White Out cleaning.

Step-by-Step Tutorial: How to Use an Olympia SM4, SM3, or SM2 typewriter - Works for SM1 & SM5. by [[Mr and Mrs Vintage Typewriter]]

Part 3: COMPLETE Olympia SM3 Service/Set Up Guide- Carriage Adjustments/ Ring and Cylinder by [[The HotRod Typewriter Co.]]

Not mentioned in the video is that, at least on his model, most of the common adjustment points have screws or nuts which have a brassy look rather than silvery almost as a means of highlighting them as subtle adjustment points for improving the performance of the machine.

Sometimes the carriage lock mechanism on the Olympia SM3 may not clear the carriage rail completely and this can result in it rubbing on the returns which results in a zipper or grinding sound. Forming the bar that connects the lever to the mechanism can quickly remedy this issue. See timestamp 2:17

Fore and aft adjustments on carriages

Details at timestamp

Side to side adjustment on carriage:

Details at timestamp

Forward and backward carriage adjustments (on both sides):

Details at timestamp

Adjustment for the spacing between the carriage rails:

This adjustment is rarely done unless there is something drastically wrong with the machine Details at timestamp

Adjustment on the carriage stoppers for how much bounce the carriage shift might have as well as how high or low the carriage sits at it's lowest point using the triangle sliding bracket on each side of the carriage with two screws. If these force the carriage too high, it can affect where the type sits in terms of potentially interfering with the bichrome settings to make letters (especially the tallest ones) have two colors when they should only have one. Details at timestamp 8:14

Adjustment on the rear springs for how light or heavy the carriage shift may be. Raise the spring and then adjust the small "nut" on the top. Details at timestamp 9:52

Ring and Cylinder adjustment for Olympia SM3<br /> Details at timestamp

Gerren doesn't seem to understand (or perhaps doesn't discuss it) some of the mechanics behind this adjustment beyond the distance of the platen to the typeface, but the usual suggestion is that the typeface shouldn't actually strike the paper and/or the platen. Ideally there should be just enough space between the typeface and the platen that an addition sheet of paper can be easily slid between the two along with the ribbon and another sheet of paper. This will allow the typeface to just kiss the ribbon and force the ink onto the front sheet of paper. Doing this will help to protect the integrity of the paper being typed on (ie, no deep imprints being pressed into the paper -- often seen with the period), as well as the integrity of the platen (preventing chips and imprints into the rubber, especially if it has been hardened), and the longer term integrity of the ribbon which can tend to be cut into by the typeface if it's too close.

From a physics perspective there is some minor amount of flex in the typebar arm between where the "hammer" at the bottom of the typebar hits the "anvil" (aka ring) and the top of the typeface which, when typing at speed will tend to "throw" the typeface a tad farther than it would hit when the hammer hits the anvil when simply holding it against the ring manually.

Part 2: COMPLETE Olympia SM3 Typewriter Service/repair- SO YOU WANT TO BE A MECHANICAL ENGINEER?!? by [[The HotRod Typewriter Co.]]

An excellent video in terms of coming to understand the functionality of a typewriter versus how the pieces interact to effectuate those functionalities.

COMPLETE Olympia SM1/2/3/4/5/7 Typewriter Build/Service/Tune up Series- Part 1 by [[The HotRod Typewriter Co.]]

Olympia SG1 1953-72 cleaning (technical restoration)

Typewriter Video Series -- Episode 262: Olympia SG1 by [[Joe Van Cleave]]

https://www.facebook.com/groups/typewritermaintenance/permalink/2310899869147449/

Details for helping to remove the platen on an Olympia SG1

Tips for Removing and Installing Olympia SM3/SM4 spring loaded typewriter keys by [[The HotRod Typewriter Co.]]

Classy Dames: Olympia SG1 and Husqvarna 6430 by MyOldTypewriter

https://www.mrmrsvintagetypewriters.com/en-us/products/olympia-typewriter-case-rubber-foot?_pos=1&_sid=f3b235259&_ss=r

Out with the Old, In with the New: Olympia SM by [[myoldtypewriter]]

They recommend fixing the Olympia SM3 spacer issue with:

Danco 1/2 rubber washer Universal (item #198804, model #88569) -- 00 trade size with 1/2" OD and 3/16" ID. https://www.lowes.com/pd/Danco-10-Pack-1-2-Rubber-Washer/3380002

The Amazing Floating Olympia by [[Michael P. Clemens]] aka clickthing

Michael recommends using 1/4" flat bibb washers with 9/16" OD to replace the rubber washers on the Olympia SM3, which notoriously are squished and need replacement. The general symptom is that the carriage sits low on the machine and scrapes or hangs on the sides of the body beneath it.

Olympia SM-3 SM-4 Typewriter Carriage Binding, Repair, Replace Body Spacers Tutorial Demo by [[Phoenix Typewriter]]

https://munk.org/typecast/2011/04/23/1964-nomda-blue-book-olympia-font-styles/

Olympia SM3 & 9 Comparison by [[Joe Van Cleave]]

The SM3 and SM4

Subtle differences between the two models.

https://munk.org/typecast/?s=fonts

One to get rid of<br /> by [[Richard Polt]]

Olympia SF Companion adjustments<br /> by [[Typewriter Justice]]

Repairing a 1961 Olympia SF

Woody Allen Has Used the Same Typewriter for 50 Years! by [[Roger Friedman]] in Showbiz411

Referenced documentary is from PBS: American Masters Woody Allen: A Documentary (2011)

Woody Allen & his Typewriter

He wrote everything with his Olympia SM3 typewriter. He lost the hood "30 years ago".

He literally cuts and staples pieces of typescripts together.

https://shopgoodwill.com/item/192255013<br /> 2024-03-02 sold<br /> $112.00<br /> 8 bids<br /> (broken space bar)

Speaks of the mountain that overlooked Olympia. Speaks of Mount Typaeum being on the way towards Olympia.

After the situation in which the woman disguised herself as a gymnastics trainer in order to be allowed in to Olympia, they had to pass a law that trainers now must strip nude before entering to ensure they are not imitating the opposite sex.

Alter of Artemis mentioned next to Leonidaeum

Leonidaeum is described.

Alters near the stadium.

Temple of pelopium

Description of the Temple of Zeus

Description of the river near Olympia

The starting point for the description of Olympia and from view we have at the start.

Trainers must strip before entering after Callipateira disguised herself like a gymnastic trainer.

Stadium Mentioned

Mention of a wall and council chamber

Another Description of a piller

Town Hall and Metroum Descriptions

Further Description of the Temple of Hera

Temple of Hera Described.

Beginning point.